# Quality Factor / Q Factor; formulas and equations

### The quality factor or Q factor is a measure of the performance of a coil, capacitor inductor in terms of its losses and resonator bandwidth. Simple formulas can relate the variables.

**Q, Quality Factor Tutorial Includes:**

Q, quality factor basics
Inductor Q
RLC network Q

the quality factor or 'q' of an inductor or tuned circuit is often used to give an indication of its performance in a resonator circuit. the q or quality factor is a dimensionless number and it describes the damping in the circuit. it also provides an indication of the resonator’s bandwidth relative to its centre frequency.

values for quality factor are often seen quoted and can be used in defining the performance of an inductor, a capacitor or tuned circuit.

the q or quality factor is used with many rf tuned circuits or elements to indicate their performance in an oscillator or other form of resonant circuit.

亚博绑定银行卡有危险吗simple formulas relate the losses and bandwidth to the q.

## Q, quality factor basics

亚博绑定银行卡有危险吗the concept of q, quality factor was first envisaged by an engineer named k. s. johnson from the engineering department of the western electric company in the us. he was evaluating the performance and quality of different coils. over the course of his investigations he developed the concept of q. interestingly his choice of the letter q was made because all other letters of the alphabet were taken and not because of the term quality factor, although with hindsight the choice of the letter q for quality factor could not have been any better.

quality factor is a concept that is applicable in many areas of physics and engineering. it is denoted by the letter q and may be referred to as the q factor.

亚博绑定银行卡有危险吗the q factor is a dimensionless parameter that indicates the energy losses within a resonant element which could be anything from a mechanical pendulum, an element in a mechanical structure, or within electronic circuit such as a resonant circuit.

while the q factor of an element relates to the losses, this links directly in to the bandwidth of a resonator with respect to its centre frequency.

亚博绑定银行卡有危险吗the q indicates energy loss relative to the amount of energy stored within the system. thus the higher the q the lower the rate of energy loss and hence oscillations will reduce more slowly, i.e. they will have a low level of damping and they will ring for longer.

for electronic circuits, energy losses within the circuit are caused by resistance. although this can occur anywhere within the circuit, the main cause of resistance occurs within the inductor.

## Quality factor definition

亚博绑定银行卡有危险吗the definition of quality factor is often needed to give a more exact understanding of what this quantity actually is.

for electronic circuits, q is defined as the ratio of the energy stored in the resonator to the energy supplied by a to it, per cycle, to keep signal amplitude constant, at a frequency where the stored energy is constant with time.

it can also be defined for an inductor as the ratio of its inductive reactance to its resistance at a particular frequency, and it is a measure of its efficiency.

## Effects of Q factor

亚博绑定银行卡有危险吗when dealing with rf tuned circuits, there are many reasons why q factor is important. usually a high level of q is beneficial, but in some applications a defined level of q may be what is required.

some of the considerations associated with q in rf tuned circuits are summarised below:

With increasing Q factor or quality factor, so the bandwidth of the tuned circuit filter is reduced. As losses decrease so the tuned circuit becomes sharper as energy is stored better in the circuit.*Bandwidth:*

It can be seen that as the Q increases, so the 3 dB bandwidth decreases and the overall response of the tuned circuit increases. In many instances a high Q factor is needed to ensure that the required degree of selectivity is achieved.In many RF applications there is a requirement for wide bandwidth operation. Some forms of modulation require a wide bandwidth, and other applications require fixed filters to provide wide band coverage. While high rejection of unwanted signals may be required, there is a competing requirement for wide bandwidths. Accordingly in many applications the level of Q required needs to be determined to provide the overall performance that is needed meeting requirements for wide bandwidth and adequate rejection of unwanted signals.*Wide bandwidth:*Any oscillator generates what is known as phase noise. This comprises random shifts in the phase of the signal. This manifests itself as noise that spreads out from the main carrier. As might be expected, this noise is not wanted and therefore needs to be minimised. The oscillator design can be tailored to reduce this in a number of ways, the chief one being by increasing the Q, quality factor of the oscillator tuned circuit.*Oscillator phase noise:*Tuned circuits and filters are often used to remove spurious signals. The sharper the filter and the higher the level of Q, the better the circuit will be able to remove the spurious signals.*General spurious signals:*As the Q of a resonant circuit increases so the losses decrease. This means that any oscillation set up within the circuit will take longer to die away. In other words the circuit will tend to "ring" more. This is actually ideal for use within an oscillator circuit because it is easier to set up and maintain an oscillation as less energy is lost in the tuned circuit.*Ringing:*

## Q factor formulas

亚博绑定银行卡有危险吗the basic q or quality factor formula is based upon the energy losses within the inductor, circuit or other form of component.

from the definition of quality factor given above, the q factor can be mathematically expressed in the q factor formula below:

when looking at the bandwidth of an rf resonant circuit this translates to the q factor formula:

within any rf or other circuit, each individual component can contribute to the q or quality factor of the circuit network as a whole. the q of the components such as inductors and capacitors are often quoted as having a certain q factor or quality factor.

## Quality factor and damping

one aspect of the q factor that is of importance in many circuits is the damping. the quality factor, q determines the qualitative behaviour of simple damped oscillators and affects other circuits such as the response within filters, etc.

there are three main regimes which can be considered when referring to the damping and q factor.

An under-damped system is one where the Q factor is greater than a half. Those systems where the Q factor is only just over a half may oscillate once or twice when a step impulse is applied before the oscillation falls away. As the quality factor increases, so the damping falls and oscillations will be sustained for longer. In a theoretical system where the Q factor is infinite, the oscillation would be maintained indefinitely without the need for adding any further stimulus. In oscillators some signal is fed back to provide an additional stimulus, but a high Q factor normally produces a much cleaner result. Lower levels of phase noise are present on the signal.*Under-damped (Q > 1/2) :*An over-damped system has a Q factor that is less than 1/2. In this type of system, the losses are high and the system has no overshoot. Instead the system will exponential decay, approaching the steady state value asymptotically after a step impulse is applied. As the Q factor or quality factor is reduced, so the systems responds more slowly to a step impulse.*Over-damped (Q < 1/2):*The critically damped system has a Q factor of 0.5 and like an over-damped system, the output does not oscillate, and does not overshoot its steady-state output. The system will approach the steady-state asymptote in the fastest time without any overshoot.*Critically damped (Q = 1/2) :*

in many rf resonant systems, high levels of q factor are needed. for filters sufficient selectivity is needed, but not too much, and for oscillators high levels of q result in improved stability and lower phase noise. in many systems the q factor should not be too high as it may result in filter bandwidths being too narrow and oscillators not being able to track over the required range. however q factor levels need tend to be high rather than low.

**More Basic Concepts:**

Voltage
Current
Resistance
Capacitance
Power
Transformers
RF noise
Decibel, dB
Q, quality factor
* Return to Basic Concepts menu . . .*